HiModel
LEOPARD 5692/1340KV 4-POLES INRUNNER BRUSHLESS MOTOR RED FOR 1/5 CARS LBP5692/3D
Model | LBP5692/3D |
Max Amps | 110A |
Lipo Cell | 4-8s |
Max Power | 5500W |
KV(RPM/Volt) | 1340KV |
Resistance | 0.0046 |
No-load Current(15V) | 4.1A |
Diameter×Length (mm) | Φ55.8×92 |
Mounting hole depth | 8mm |
Length of extend Shaft | 20mm |
Shaft Diameter (mm) | Φ6.0 |
Weight | 880g |
, , , , , , Specifications:, , , , , , , , , , , , ,
Features: - High efficiency up to 95% - Powerful 4-pole ...HiModel
LEOPARD 5692/1000KV 4-POLES INRUNNER BRUSHLESS MOTOR RED FOR 1/5 CARS LBP5692/4D
Model | LBP5692/4D |
Max Amps | 78A |
Lipo Cell | 5-10s |
Max Power | 5500W |
KV(RPM/Volt) | 1000KV |
Resistance | 0.0073 |
Diameter×Length (mm) | Φ55.8×92 |
Mounting hole depth | 8mm |
Length of extend Shaft | 20mm |
Shaft Diameter (mm) | Φ6.0 |
Weight | 880g |
, , , , , , Specifications:, , , , , , , , , , , No-load Current(15V) : 3A, , ,
Features: - High efficiency up to 95% - Powerful 4-pole ...HiModel
36MHZ WFT08 8-CHANNEL PCM/PPM RADIO SYSTEM
MODEL NO. | WFT08 |
●Band | 36 MHz |
●Output | ≤750mW |
●Current drain | ≤300mA |
●Output pulse | 1000μs-2000μs |
●Modulation | PPM/PCM |
●RF module | individual |
●Power | 1.2v×8 (9.6v) Ni-cad/Ni-MH rechargeable batteries |
RECEIVER type | WFR08-P PPM |
, , , , , , Specifications:, , , , , , , , , , , TRANSMITTER, 1.5v×8(12v) normal alkalescence batteries, * Both mode 1 & mode 2 are available, mode 2 will be provided by default for international orders, you can specify the stick mode by leaving a message in the Remark field on the last step when place the order., *This radio come in white foam packing only, no outer color carton., , ,
Features: 8 Channels transmitter Specification and features 1. Model: WFT08 ...HiModel
RCEXL OPTO GAS ENGINE KILL SWITCH
, , , , , , Specifications:, , , , , , , , , , , This device plugs into a spare receiver channel., This is a must have safety device for any gas powered plane!, This device allows you to safely kill your engine at anytime(on the ground, or in the air!), Or when out of control also allows kill the enfine., , ,
Features: This device allows you to safely and remotely kill ...4 Reviews
HiModel
WFLY 2.4G 9-CHANNEL RECEIVER WFR09S
Receiver Model | WFR09S |
Range test in ground | more than 900M |
Dual MCU, dual antenna receiver | Contains two receivers working independently |
, , , , , , Specifications:, , , , , , , , , , , 2.4GHz receiver (WFR09S) 9 channel 2.4GHz dual MCU, dual antenna receiver, Use in:airplane, helicopter, glider, car, boat, Band:2.400GHz-2.4830GHz ( varies with different country and region), Receive sensitivity:-97dBm, Fail safe, quick recover signal, Modulation:PPM/PCMS 1024/PCMS 4096, Power:4.8-6V, Dimension:44.8×27.9×16.39mm, Weight:14.8g, Features:, Choose the optimum signal for antenna, More reliable, Quicker response, Better anti-interference, Longer range, , ,
Features: A. Hopping frequency is high Speed. WFLY 2.4G adopted ...5 Reviews
HiModel
CORONA 8-CHANNEL 2.4G TWO-WAY RF MODULE & RX SYSTEM FOR FUTABA TRANSMITTER CT8FD/CR8FD
Transmitter modules | CT8FD |
Hitec | Optic 6, Eclipse 7, Prism 7 |
WFLY | WFT09, WFT08 |
Receiver module | CR8FD, 8 channel |
Operation Voltage Range | 6~13V |
Operation Voltage Range | 4.8~6V |
Sensitivity | -100dBm |
Resolution | 10bit |
, , , , , , Specifications:, , , , , , , , , , , Compatible with following transmitters:, Futaba 3PK, 3PM, 7U, 8U, 8J, 9C, 9Z, 10C, FN SERIES, T10C, FC-18, FC-28, FF7, Compatible with any Corona two-way transmitter module, Electrical Specifications:, Transmitter module:, Operating Current: , RF output power:, Receiver module:, Operating Current: , , ,
Features: THIS IS THE AFHSS 2.4G TWO-WAY COMMUNICATION SYSTEM FROM ...HiModel
FRSKY 2.4G FUTABA COMPATIBLE RF MODULE (TWO-WAY) & RECEIVERS COMBO DFT/V8FR
Operating Voltage Range | 4.8V-6V |
Operating Current | 30mA |
Specified Range | 1.2km |
Resolution | 10bit |
Latency | 22ms |
Number of Channels | 8CH |
Dimensions | 60×37×21 mm |
Model | DFT, two-way telemetry module |
Operating Voltage Range | 6.0V-13.0V |
Operating Current | 50mA |
Output Power | 60mW |
Resolution | 11bit (3072) |
Futaba | 3PM, 3PK, 7U, 8U, 8J, 9C, 9Z, 10C, FN series, T10C, FC-18, FC-28. |
Hitec | Optic 6, Eclipse 7, Prism 7. |
WFLY | WFT09, WFT08. |
, , , , , , Specifications:, , , , , , , , , , , Receiver specifications:, Transmitter module specifications:, Compatible with the following transmitters:, , ,
Features: ◆ Advanced Continuous Channel Shifting Technology ( ACCST SYSTEM) ...4 Reviews
HiModel
FRSKY 2.4G JR COMPATIBLE RF MODULE (TWO-WAY) & RECEIVER COMBO DJT/V8FR-HV
Operating Voltage Range | 4.8V-6V |
Operating Current | 30mA |
Specified Range | 1.2km |
Resolution | 10bit |
Latency | 22ms |
Number of Channels | 8CH |
Dimensions | 60×37×21 mm |
Operating Voltage Range | 6.0V-13.0V |
Operating Current | 50mA |
Output Power | 60mW |
Resolution | 10bit |
Dimensions | 63.9X48.5X36.5mm (V8JT); |
, , , , , , Specifications:, , , , , , , , , , , Receiver specifications:, Transmitter module specifications:, , ,
Features: * The RF module of this combo was upgraded ...3 Reviews
HiModel
FRSKY TWO-WAY 2.4G FUTABA COMPATIBLE RADIO SYSTEM TELEMETRY DFT/D8R-II PLUS
Model | DFT |
Operating Voltage Range | 6.0V-13.0V |
Operating Current | 50mA |
Output Power | 60mW |
Resolution | 11bit (3072) |
Futaba | 3PM, 3PK, 7U, 8U, 8J, 9C, 9Z, 10C, FN series, T10C, FC-18, FC-28. |
Hitec | Optic 6, Eclipse 7, Prism 7. |
WFLY | WFT09, WFT08. |
Model | D8R-II Plus |
Weight | 16.2g |
Dimension | 54*27*17mm |
Operating Voltage Range | 4.0V-7.2V |
Operating Current | 100mA |
Specified Range | 1.5km (Ground Range) |
Resolution | 11bit (3072) |
Latency | 22ms |
Number of Channels | 8CH |
Analog voltage | 0~3.3V |
, , , , , , Specifications:, , , , , , , , , , , Transmitter module specifications:, Compatible with the following transmitters:, Receiver specifications:, , ,
Features: The Two-way Radio System developed by FrSky provides an ...2 Reviews
HiModel
FRSKY TWO-WAY 2.4G DHT MODULE - TOGGLE SWITCH VERSION
Operating Voltage Range | 6.0V-13.0V |
Operating Current | 50mA |
Output Power | 60mW |
Resolution | 3072 (>11bit) |
, , , , , , , , Features:, , , , , , , , , , , THIS IS THE NEW TOGGLE SWITCH VERSION DHT., 1.1 Compatibility:, Switch 1, , Switch 2, , Mode of DHT, , Compatibility, , OFF, , OFF, , Two-way Mode, , Two way telemetry receivers (D8R, D6FR), , OFF, , ON, , V8 Mode, , V8 receivers (V8FR-HV, V8R7-HV, V8R7-SP, V8R4), , 1.2 Specifications:, 2. Setup, 2.1 Installation process:, 1)Open the transmitter, find out Battery power supply line, PPM signal line, and GND., 2)Take the order and solder Battery power supply line, PPM signal line, and GND to DHT with 3 wires., (RED→V+; BLACK→GND; YELLOW→PPM), 3)Drill one hole on the transmitter to install the PCB with F/S button, GREEN/RED LED and two switches., 4)Connect the antenna connector at the port on transmitter board., 5)Drill a hole for antenna connector at suitable space on the transmitter (diameter 7mm is suitable)., 6)Fix the transmitter antenna on the connector .Turn the transmitter power on and check the power indicator LED, which is normally light RED., 2.2 Bind procedure, 1)Turn your transmitter on and switch it to PPM mode. Turn your transmitter off., 2) Turn your transmitter on while holding the F/S button on the transmitter module (Please make sure DHT is in its corresponding mode when working with V8 or two way telemetry receivers). Release it in a few seconds. The RED LED on the transmitter module will flash, indicating the transmitter is ready to bind the receiver., 3)Connect battery to the receiver while holding the F/S button on the receiver. The RED LED on the receiver will flash, indicating the binding process is completed., 4)Turn on the transmitter and re-connect battery to the receiver. The RED SOLID LED on the receiver will indicate the receiver is receiving commands from the transmitter., 5)After the above steps are completed, both the transmitter and the receiver are ready to be used., Notice: When working with two way telemetry receivers (D8R or D6FR), please kindly make sure that the battery ,
Features: THIS IS THE NEW TOGGLE SWITCH VERSION DHT. 1.1 ...1 Reviews
HiModel
ZEROUAV 900MHZ DATA LINK MODULE/DATA RADIO
Power supply | 3-6S Lipo |
Power connector type | XT60 |
Working frequency | 900mHz |
Range | 2-3KM (air to ground, for reference only) |
Antenna type | 900mhz, 5db |
Working current | 16mA @ 25V, 6S Lipo |
Working speed | 115200 bit |
Signal connector | standard SMA |
, , , , , , Specifications:, , , , , , , , , , , ZeroUAV 900Mhz Data Link Module/Data Radio, , ,
Features: Data radio for YS-X6 and YS-X4. Includes/Requires: Includes: 2 ...HiModel
FRSKY TWO-WAY 2.4G JR COMPATIBLE RADIO SYSTEM TELEMETRY DJT/D8R-II V2
Model | DJT |
Operating Voltage Range | 6.0V-13.0V |
Operating Current | 50mA |
Output Power | 60mW |
Resolution | 11bit (3072) |
Model | D8R |
Weight | 16.2g |
Dimension | 54*27*17mm |
Operating Voltage Range | 4.0V-7.2V |
Operating Current | 100mA |
Specified Range | 1.5km (Ground Range) |
Resolution | 11bit (3072) |
Latency | 22ms |
Number of Channels | 8CH |
Analog voltage | 0~3.3V |
, , , , , , Specifications:, , , , , , , , , , , Transmitter module specifications:, Compatible with the following transmitters:, JR: 347/388/783/U8/PCM10/PCM10S/PCM10SX/, PCM10IIS/8103/J9303/MX-22/MX-24S/PX/9XII., Receiver specifications:, , ,
Features: The Two-way Radio System developed by FrSky provides an ...2 Reviews
HiModel
SUPER-LINK 2.4 GHZ TX MODULE CW-8
Dimension | 52x33.5x12.5mm |
Operating Voltage | 3.7~4.2V(connect with 1S battery); 7.4~12.6V(power supplied by Transmitter) |
Resolution | 1μs |
Operating current | 30mA |
, , , , , , Specifications:, , , , , , , , , , , SUPER-LINK 2.4 GHz Module CW-8, Power:, , ,
Features: Features ●Long Range, light weight ●Easy to bind and ...3 Reviews
HiModel
JBA J15G 15CC PETROL ENGINE FOR AIRPLANE
Engine Type | Gasoline Two-stroke, Air Cooled |
Displacement(cc) | 14.93cc (.90 c.i.) |
Bore x Stroke (mm) | 27.8 x 24.6 |
Carburetor | Walbro WT series (Diaphragm & butterfly valve) |
Maximum output | 3.2HP @ 12000RPM |
RPM range | 1800 to 13000 RPM |
Ignition | Auto advanced Rcexl DC-CDI with special spark plug cap |
Spark plug type | 1/4*32 Rcexl |
Lubrication oil | 2 cycle engine oil API TC/JASO FD or better specs. (Mobil +M2T) |
Recommended propellers | 13x8 to 15x8 (two blades) |
Weight | 635g (without ignition and muffler) |
, , , , , , Specifications:, , , , , , , , , , , Specifications, Ignition power DC 4.8V (4 cell NiCad or NiMh battery) * don't use higher than 4.8V., Break-in fuel oil ratio: 25:1 (4%), General use fuel: 33:1 (3%), 824g complete, , ,
Features: This is a new generation of small gas quality ...1 Reviews
HiModel
NGH 9CC PETROL ENGINE FOR RADIO CONTROL AEROPLANE GT9
Engine Type | Gasoline Two-stroke, Air Cooled |
Displacement (cc) | 9.07cc |
Bore x stroke (mm) | 23.35 x 21.2 |
Carburetor | NGH made 60G needle with pump membrane |
Max output | 0.8HP@15000RPM |
RPM Range | 2600-15000RPM |
Ignition | Auto advanced Rcexl DC-CDI with special spark plug cap |
Spark plug type | 1/4 x 32 Rcexl |
Ignition Power | 4.8V |
Lubrication Oil | 2 cycle engine Oil API TC/JASO FD or better specs. (Mobil + M2T) |
Recommended propellers | 10 x 6 to 12x6 (two blades) |
Weight | 425g (without ignition) |
, , , , , , Specifications:, , , , , , , , , , , Break-in fuel oil ratio: 20:1 (5%), General use fuel: 25:1 (4%), (Oil percentage can not less than 4%), 545g complete, , ,
Features: This is a new generation of small gas quality ...11 Reviews